Mechanical and Electrical Technology VI -- Preface, Committees and Sponsors -- Table of Contents -- Chapter 1: Thermal and Mechanical Research, General Mechanical Engineering -- Prediction the Springback in Air-Bending Process Using Neural Network Metamodel -- Dynamic Equilibrium Configurations of Multibody Systems -- Wear Behaviour of Stellite 6 Coatings Produced on an Austenitic Stainless Steel Substrate by Laser Cladding Using Two Different Heat Inputs -- Influence of Pipe Diameters on Shapes of Air Taylor Bubbles in Small Pipes Containing Stagnant Water -- On the Use of Composite-Steel Joint for Semi-Monocoque Frame Design -- Influence of Blast Wave on Behavior of Steel Plate -- The New Rolling Mill Gearbox Concept Design -- Numerical Analysis for Resistance Calculations of NPL as a Floating Hull for Wave Glider -- Design of a Simple Underactuated Mechanical Gripper -- Evaluation of the Performance of Micro-Drills in Drilling a Machinable Ceramic Material -- Parametric Optimization in Turning of CFRP (Epoxy) Composites: A Case Experimental Research with Exploration of HS Algorithm -- NET3D Calculation on the Depth of Penetration by a Long-Rod Penetrator with Varying Obliquity -- Simulation on the Life Expectancy of Fine Blanking Punch for Recreation Vehicle Seat Recliner Sector Tooth -- Utilization of Tooth Contact Pattern in a Gear Meshing Model for Estimation of Sliding Loss in a Parallel-Axis Gear Pair -- Field Investigation on Thermal Performance of the Tile Ventilator -- Computer Aided Design of the Die-Set for Sheet Metal Punching and Blanking Dies -- A Hybrid Approach for Process Optimization in Taper Cutting Operation Using Wire Electrical Discharge Machining -- Optimization of the EDM Parameters on Machining Ti-6Al-4V Alloy with Multiple Quality Characteristics.

Transient Radiation Coupled With Conduction Heat Transfer in a One Dimensional Slab -- Thermodynamic Analysis of Hydrogen Production from Methanol Reforming in Supercritical Water -- A CAPP/CAD for Sheet Metal Deep Drawing -- The Effect of Rise Angle of V-Hull Non Ballast Ship on Resistance Performance -- Synthesis of Rigid-Body Guidance Mechanism with Path and Pose Generation Independently -- The Effects of Injection Timing on BDF in an IDI Diesel Engine -- Heat Transfer Enhancement due to V-Shaped Perforated Blocks in a Solar Air Heater Duct -- The Performance of the Interlocking Block Solar Collector -- SOx Reduction by Feedwater in an Industrial Boiler -- Chapter 2: Tools and Electrical Engineering -- Development of an Oscillating Drum Granulator Prototype for Cassava Pearl -- Optimization of the Thrust Ripple of a Tubular Flux-Switching Permanent Magnet Linear Motor -- Design, Fabrication and Evaluation of a Novel Electro Thermal Micro-Gripper for Handling of Head Gimbal Assembly -- 2x2 Rectangular-Slot Microstrip Array Antenna for WLAN Applications -- An Effective Implementation of the Nonlinear Homotopy Method for MOS Transistor Circuits -- Parallel-Connected High Voltage Multiplier with Symmetrical Structure -- Electrical Energy Conservation in Engineering Industry: A Case Study -- Space Frame Analysis, Design, and Testing for Electric Vehicle Formula -- Effect of Grain Size on Effective Permittivity of Ferroelectric Films Based on Effective Medium Theory -- Chapter 3: Mechatronics and Robotics -- Mechanism Design and Manipulating Algorithm for Orientation Changing Module with Three Flexible Links -- An Innovative Motion Planning for 4-DOF PKM -- An Altitude Estimation Technique for Autonomous Landing of a Quad-Rotor Using a Vision System -- Dexterity Measures for 4DOF Exoskeleton Robot.

Weld Bead Tracking Control of a Magnetic Wheel Wall Climbing Robot Using a Laser-Vision System -- Implementing Expandable Path for an Resizable Cobot -- A μP-μC-FPGA Synergy Controller for a Linear Delta Robot -- The Performance of a Delta Telerobot -- Design Morphological Changing All-Terrain-Rover and Optimizing with Genetic Algorithm for Enhancing Mobility -- A Low-Cost Stereo Vision System for Real-Time Pose Estimation and its Application for Robot Tracking -- A Study on Mobile Gait Rehabilitation Training Robots -- Chapter 4: Control and Automation -- A Weighting Slope MPPT Method Based on Sun Tracking Applied in PV System -- Experiment of the State Variable Feedback for a Quadrotor -- Vibration Rejection and Stabilization Control for an Inertial Stabilization System -- Study on Dynamic Characteristics of DC Valve in Electro-Hydraulic System Using CFD Simulation -- Gain-Scheduled Control Approach by Logarithm Transformation for Electrical Vehicle Traction Force Control -- Evaluation of Deadband Effect in Steer-by-Wire Force Feedback System by Using Driving Simulator -- A New Stator Flux Estimation Method for Direct Torque Control of Electrical Excitation Flux-Switching Generator -- Tracking Control for the Center-of-Gravity Constant Shift of Omnidirectional Rehabilitative Training Walker -- Process Control Virtual Laboratory: Temperature Control Based on LabVIEW for Convection Heat Transfer -- Chapter 5: Information Technologies, Data and Signal Processing -- Improved SPIHT Algorithm for Texture Image Compression -- 10.3125Gbps High-Speed SFP+ Channel Signal Integrity Evaluations -- A New Analytical Approach to Estimate Fading in Mobile Communication System Design -- Driver Behavior Detection Based on Multi-GNSS Precise Point Positioning Technology -- Complex Network Based Modeling and Analysis of Resource Nodes for MG.

Evaluating the III-Posedness of Inverse Problem to Size Flaws from Eddy Current NDT Signals Obtained with an Absolute Type Probe -- Low-Complexity Multiplication Using Complement and Signed-Digit Recoding Methods -- Comparative Study on Wear Particle Colour Classifications Using Various Machine Learning Algorithms -- Design and Implementation of Linux-Based Supervisory and Control Configuration Software for Automatic Billet Cut-to-Length System -- Chapter 6: Industrial Engineering -- Modeling for Materials and Logistics Optimal System in JIT Flexible Manufacturing -- A Study of a Single-Period Model for the Parallel Fleet Replacement Problem -- Eco-Driving Rating Based on Average Trip Speed and Evaluation -- Palm Oil EFB: Green Energy Source in Malaysia -- Applying Kalman Filter for Correlated Demand Forecasting -- Fuzzy-TOPSIS for Appropriate Site Selection for Establishing a Thermal Power Plant -- Keywords Index -- Authors Index.